Driveways look simple until the concrete dries and every pass you made is still visible. The fix is order of operations, not a bigger number on the box.
Set the machine up for flatwork
For a typical residential driveway, a gas washer in the mid-2 GPM range is the comfortable tool. The Westinghouse WPX3400 and the Simpson PS3228 are the two homeowner machines compared for that job. An electric will do a short pad. It will make a long stained drive feel endless. The comparison is in the gas guide and the electric guide.
Add a surface cleaner that is rated for your washer’s PSI and GPM, not above it. The surface cleaner guide has the ceilings. A 15-inch deck such as the Simpson 80165 or the Westinghouse 15-inch cleaner is a fair match for homeowner gas flow, if you stay under that deck’s PSI ceiling. Do not hang a deck rated to 3.0 GPM on a 4.0 GPM pump.
Hose length is the other comfort. Fifty feet of hose rated at or above the washer’s maximum PSI lets the machine stay put. The hose guide separates the 3,100 PSI hose from the 4,000 PSI hose. Use the one that clears your machine.
Before any water
Sweep the grit. Pressure washing loose sand just sandblasts the concrete and your ankles. Move vehicles, doormats, and anything that should not get chemical. Wet plants you want to keep, and cover outlets.
Look at the stains. Tan organic film is mildew and dirt. Dark spots that bead water are usually oil. They need a cleaner made for petroleum, time, and sometimes a second application. Pressure by itself lightens the halo and leaves the middle. The soap guide separates a bleach-free concentrate labeled for a soap system from cleaners you should apply with a pump sprayer.
If your city tells you not to send wash water down the storm drain, believe the city. A driveway that drains to the street is the common case. Know the rule before you mix the chemical.
The sequence
- Connect the water, purge air from the garden hose, then start the washer. Squeezing the trigger before the pump is running, on a machine that has water, is how you avoid a dry start. Follow your manual if it says otherwise.
- Apply cleaner with the soap tip or a pump sprayer, not with a 15-degree tip. Cover the concrete evenly. On a slope, work so the chemical does not all run to the bottom before it has sat.
- Wait the time the label allows. Do not let it dry. If it starts to dry, mist it, do not just hit it with high pressure yet.
- Rinse with the surface cleaner in overlapping paths, the way you would mow. The second pass should cover the line left by the shroud. Keep the deck on the concrete. The Simpson manual is blunt about not lifting a spinning deck.
- Do edges, steps, and the strip against the garage with a fan tip on the wand. A 15-degree tip is reasonable on sound concrete if you keep it moving and stay several inches off. Stop if you see aggregate appearing. You are cutting the surface.
- Treat remaining oil with cleaner and a stiff brush, then rinse that spot again. Some oil is in the pores. You can fade it and still see it. That is a stain, not a failed washer.
- Rinse chemical off plants, flush the soap system with clear water, and coil the hose without a kink.
Marks people make
Hovering writes a bar into the concrete that shows up when it dries. A 0-degree tip writes a line you cannot rinse out. Starting at the bottom of a slope and blowing dirty water back across a clean section makes you wash it twice. Skipping the overlap is the stripe pattern.
If the surface cleaner pulses, shut down, release pressure, and clean the nozzles. A clogged jet is the usual cause, and it will also load the pump.
Sealed or painted concrete can peel. Test a corner. If the sealer is what you liked about the driveway, pressure washing may remove the sealer and leave you with a reseal job. That can still be the right outcome. It should be a decision, not a surprise.
When the concrete is clean and dry, look at it from the end of the drive in low sun. That is when the missed strips show. One more overlapping pass is cheaper than explaining them later.