We may earn a commission when you buy. The price stays the retailer's.

Advertising disclosure

How-to

How to choose PSI and GPM

PSI is how hard the water hits. GPM is how much water arrives. The surface, the nozzle, and your distance from it decide whether those numbers clean or damage.

Updated November 18, 2026 · By Eric

Two numbers sell every pressure washer. One of them is doing less work than the carton implies.

PSI is force. It is also a test condition.

PSI is pounds per square inch. A higher number can knock soil off a harder surface. It can also cut a groove in a deck board if you stand still with a narrow tip.

Makers do not all print the same kind of PSI. Watch the word next to the number.

  • Maximum is a peak. Sun Joe’s SPX3000 manual lists 2,030 PSI maximum and, in the same table, 1,450 PSI rated under typical load.
  • Rated or working pressure is the more honest expectation once a nozzle is installed.
  • A standard such as PWMA PW101 or CETA CPC-100 means the maker is pointing at a test method. The Ryobi Amazon listing linked from the electric guide says its 2,300 PSI and 1.2 GPM figures were tested to PW101. The model field on that page is AR2N1.

If a listing gives you only one number and no test note, treat it as a ceiling, not as what you will feel on a 25-degree tip at the end of a 50-foot hose.

GPM is the clock

GPM is gallons per minute. It is the bucket you are throwing, not how hard you throw it. The electrics in the electric guide cluster around 1.1 to 1.8 GPM. The homeowner gas machines in the gas guide cluster around 2.4 to 2.6 GPM. The contractor DeWalt is 4.0 GPM and, in its manual, wants a water supply of 5 GPM.

That gap is why a driveway goes faster with gas even when the PSI numbers look similar. It is also why a surface cleaner sulks behind a small electric. The deck needs enough water to spin and to carry dirt out of the shroud.

Your spigot has to keep up. If the hose from the house collapses or the pump hammers, you are asking for more water than the plumbing is giving. Fix that before you blame the washer. Never run the pump dry to “see if it starts.”

Ranges that match real surfaces

These are working ranges, not permissions to ignore the manual. Distance and tip angle change the force more than people expect. Start farther away than you think.

Surface Pressure to start with Tip Notes
Cars and paint Under 2,000 PSI 40° Rinse loose grit before any mitt touches the paint.
Wood decks Often under 1,500 PSI 25° or 40° Softwood marks easily. See the deck guide.
Vinyl and siding Low, with soap doing the work 25° or 40° Spray downward. High pressure forces water behind laps.
Concrete 2,500 PSI and up, with flow 15° or a surface cleaner Oil still needs chemical.
Second-story walls Whatever the widest safe fan allows 25° or wider From the ground. Not from a ladder.

A 0-degree tip is not on that table as a starting point. It is a cutting stream. Fluid injection through skin needs medical care even when the puncture looks minor.

Nozzle, distance, dwell

The same washer is three tools depending on the tip. A black soap tip drops pressure so chemical can sit. A 25-degree green tip rinses. A 15-degree yellow tip works on concrete when you keep it moving. Orifice size has to match the pump. The nozzle guide covers the Simpson 3.0 and 4.0 sets and why the larger hole is not the upgrade.

Chemical dwell is the other half of PSI. Mildew on siding comes off with the right cleaner and a gentle rinse, not with a closer wand. Read the soap guide before you pour anything into a tank. Bleach and pumps do not belong together unless both labels say so.

If you remember one habit, make it this: believe the lower published number, start with the wider tip, and move in only until the soil leaves. The machine you already own is usually enough once the tip and the chemical match the surface.

Questions people ask

What is a cleaning unit?

Some makers multiply PSI by GPM and call the result cleaning units. It is a shorthand, not a test you can watch. Use it only to remember that a high PSI with very little flow can lose to a lower PSI with more water.

Why does my washer feel weaker than the box?

The box often prints a maximum. Sun Joe, for example, also publishes a lower rated pressure for the SPX3000. A fan tip, a long hose, and a weak spigot all reduce what you feel at the wand.

Does more PSI clean faster?

Up to the point where you damage the surface, extra pressure removes stuck soil that flow alone will not. Past that point you are cutting wood, etching concrete, or driving water behind siding. Flow is what shortens a rinse.

More guides